[Bendpak: 9APF] 9,000lb Cap. (Chain Over) Base Plate

Capacity
Lifting Capacity	9,000 lbs (4,082 kg)
Max Capacity / Front Axle	4,500 lbs (2,041 kg)
Max Capacity / Rear Axle	4,500 lbs (2,041 kg)
Maximum Capacity per Lift Arm	2,250 lbs (1,021 kg)
Dimensions
A – Width Overall	136 or 146 in (3,453 or 3,707 mm)
B – Base Plate Width	25.25 in (642 mm)
C – Post Height	123 in (3,128 mm)
D – Drive-Thru	91 or 101 in (2,311 or 2,565 mm)
E – Inside Posts	108.25 or 118.25 in (2,749 or 3,003 mm)
F – Outside Posts	129.5 or 139.5 in (3,289 or 3,543 mm)
G – Minimum Height with Pad	4.5 in (114 mm)
H – Max. Lifting Height	73.5 in (1,867 mm)
I – Max. Rise	70 in (1,775 mm)
J – Maximum Pad Adjustment	2.25 in (55 mm)
K – Floor Plate Height	1.4 in (36 mm)
L – Floor Plate Width	9.5 in (240 mm)
Arms & Pads
M – Front Arm Reach	22.25−47.5 in (562−1,205 mm)
N – Rear Arm Reach	29.5−57 in (747−1,446 mm)
Safety
Safety Lock Positions	14 (Spaced Every 3.6"/92 mm)
Standard Motor	208-230 VAC, 50/60 Hz, 1 Phase, 5 HP, 23 Amps
Time to Full Rise	≈60 seconds
Sound Pressure	Less than 85dB when in operation.
Operating Hydraulic Pressure under Max. Load	2,170 psi

The 9APF Two-Post Lift: Maximize Your Space. Master Your Fleet.

 

Stop compromising on the bays you use or the vehicles you service. The 9APF brings a full-featured, heavy-duty lift to shops with low ceilings, tight layouts, and mixed-fleet demands.

 

Base Plate Design: Unrestricted Headroom

 

The Base Plate design and short columns eliminate the overhead beam that slows down so many shops.

• Real Headroom: High-roof vans and ladder racks get the vertical clearance they need. Techs can stand upright, move freely, and work without crouching or twisting.

• Clearer Space: No overhead clutter means better lighting, simpler tool storage, and no clashes with ceiling fans, ducting, or door rails.

• Use Awkward Bays: Install a fully functional two-post lift where others won't fit, turning unused square footage into profitable revenue bays.

• Master the Fleet: Handles both tall vehicles (due to the clear vertical path) and low sports cars (thanks to dropped pad receivers). One lift, fewer compromises.

 

Extra-Low Floorplate: Fast and Safe Workflow

 

The 9APF features an extra-low steel cover plate that dramatically reduces step-over height.

• No Snags, Full Flow: Transmission jacks, oil drain caddies, and creepers roll across cleanly, eliminating workflow bottlenecks.

• Contained Lines: Hydraulic and equalizer lines are routed neatly inside the plate, creating a tidy, trip-free work area with faster cleanup and easy service access.

 

AP-Series Arms: Precision Spotting

 

The advanced AP-Series arm geometry is built for modern chassis variation.

• Triple-Telescoping: Low-profile arms reach deep and retract compactly for smaller bays.

• No Setup Hacks: Dropped pad receivers let you access lift points on lowered vehicles cleanly, without ramps or shims.

• Bi-Metric Control: Choose Symmetric for balanced service or Asymmetric for optimal door swing and front-end access. The choice is yours for faster, repeatable setup.

 

Safety You Trust

 

• Lock and Load: BendPak’s automatic swing arm restraints (ASARS) lock the arms with full-circle engagement as the lift loads, preventing arm walk-out.

• Redundant Protection: Mechanical lock positions run the full height of each column, and a single-point lock release offers controlled lowering.

• Built for Uptime: Robust construction, flexible narrow/wide install options, and accessible service points ensure the 9APF holds up to high cycle counts.

 

Who is the 9APF For?

 

The ideal solution for quick lanes, fleet garages, independent shops with mixed fleets, and growing operations looking to convert low-ceiling corners into revenue-generating service bays.

- Local Installation (Phoenix-Metro): $850 (See Install Map for additional installation costs outside of the Phoenix-Metro Area).

 

- Nationwide Free Shipping

Open Warranty